Influence of Shear Homogeneity on Flow-induced Crystallization of Isotactic Polypropylene

Hao-ran Yang; Jian-zhu Ju; Jie Lu; Jia-rui Chang; Feng-mei Su; Liang-bin Li

doi:10.11777/j.issn1000-3304.2017.17048

您当前的位置：

首页 >

文章列表页 >

Influence of Shear Homogeneity on Flow-induced Crystallization of Isotactic Polypropylene

Research Article | 更新时间：2021-01-27

- Influence of Shear Homogeneity on Flow-induced Crystallization of Isotactic Polypropylene
- Acta Polymerica Sinica Issue 9, Pages: 1462-1470(2017)
- 作者机构：
  
  国家同步辐射实验室中国科学技术大学合肥 230026
- 作者简介：
- 基金信息：
- DOI：10.11777/j.issn1000-3304.2017.17048
  CLC：
- Published：2017-9，
  
  Received：15 March 2017，
  
  Revised：13 April 2017，
扫描看全文
Hao-ran Yang, Jian-zhu Ju, Jie Lu, Jia-rui Chang, Feng-mei Su, Liang-bin Li. Influence of Shear Homogeneity on Flow-induced Crystallization of Isotactic Polypropylene. [J]. Acta Polymerica Sinica (9):1462-1470(2017)
DOI：

Hao-ran Yang, Jian-zhu Ju, Jie Lu, Jia-rui Chang, Feng-mei Su, Liang-bin Li. Influence of Shear Homogeneity on Flow-induced Crystallization of Isotactic Polypropylene. [J]. Acta Polymerica Sinica (9):1462-1470(2017) DOI： 10.11777/j.issn1000-3304.2017.17048.

摘要

固定应变和最终应变速率，采用瞬时和缓慢2种电机加速方式对样品施加剪切，研究了流场加载模式对样品流变和结晶行为的影响.实验结果显示缓慢加速能够消除剪切过程中流场的非均匀性，使样品取向度增加，提高流场对聚合物熔体的作用效果.同时，流动诱导结晶对于加速时间有依赖性.对于速率为17.7 s

-1

的剪切，加速时间为1 s时，熔体流动均匀且流动诱导的晶体取向最强，短加速时间（0.5 s）和长加速时间（1.5 s）样品的流动诱导结晶效果都弱于加速时间为1 s的样品.但是，对于不同剪切速率，其对应的最优加速时间不同.对于流动诱导结晶来说，加速时间应当作为一个重要参数来考虑，其背后的真实物理含义还需要进一步研究来说明.

Abstract

Influence of shear homogeneity on rheology and flow-induced crystallization (FIC) behavior of polymer is investigated by contrasting the sudden startup shear with the slow shear rate ramp-up procedure. The shear experiments are performed

via

changing only the rate ramp-up time at a fixed shear rate of 17.7 s

-1

and a constant strain of 20. And the corresponding motor acceleration time is set to 0

0.5

1.0 and 1.5 s

respectively. Combining wide angle X-ray scattering and polarized microscopy characterization

this set of experiments is designed to study the rate ramp-up time dependence of the rheological properties and FIC at the same shear rate and strain. When the rate ramp-up time is 0.5 s

it is found that a slow acceleration cannot completely eliminate the flow inhomogeneity. The stress overshoot still occurs in the stress-strain curve and the sample orientation is only slightly improved. As the rate ramp-up time is further increased to 1.0 s

the stress overshoot disappears

indicating that the inhomogeneity induced by destruction of melt structures vanishes. In this case

the degree of sample orientation is further improved

and the amount of oriented crystals is increased. However

when the rate ramp-up time is 1.5 s

the effect of flow induced crystallization is weakened

which is indicated by a decrease in orientation degree and the amount of oriented structures. Results obtained sufficiently illustrate that the FIC is dependent on the rate ramp-up time. However

a slower rate ramp-up procedure is not always associated with a better the flow-induced crystallization. Actually

there exists an optimal rate ramp-up time for a fixed shear rate. In addition

the optimal rate ramp-up time is not the same for different shear rates. These results suggest that rate ramp-up time should be considered as a critical parameter for FIC. And the underling mechanism still needs further investigation.

关键词

均匀剪切速率上升时间流变结晶

Keywords

Shear homogeneityRate ramp-up timeRheologyCrystallization

references

H Janeschitz-Kriegl , E Ratajski , M Stadlbauer . . Rheol Acta , 2003 . 42 355 - 364 . DOI:10.1007/s00397-002-0247-xhttp://doi.org/10.1007/s00397-002-0247-x.

X Sun , H Li , J Wang , S Yan . . Macromolecules , 2006 . 39 8720 - 8726 . DOI:10.1021/ma062105dhttp://doi.org/10.1021/ma062105d.

R H Somani , L Yang , L Zhu , B S Hsiao . . Polymer , 2005 . 46 8587 - 8623 . DOI:10.1016/j.polymer.2005.06.034http://doi.org/10.1016/j.polymer.2005.06.034.

O O Mykhaylyk , P Chambon , C Impradice , J P A Fairclough , N J Terrill , A J Ryan . . Macromolecules , 2010 . 43 2389 - 2405 . DOI:10.1021/ma902495zhttp://doi.org/10.1021/ma902495z.

F Z An , X Q Gao , J Lei , C Deng , Z M Li , K Z Shen . . Chinese J Polym Sci , 2015 . 33 688 - 696 . DOI:10.1007/s10118-015-1617-zhttp://doi.org/10.1007/s10118-015-1617-z.

P J Flory . . J Chem Phys , 1947 . 15 397 - 408 . DOI:10.1063/1.1746537http://doi.org/10.1063/1.1746537.

G S Yeh , K Hong . . Polym Eng Sci , 1979 . 19 395 - 400 . DOI:10.1002/(ISSN)1548-2634http://doi.org/10.1002/(ISSN)1548-2634.

M M Zhang , L Y Zha , H H Gao , Y J Nie , W B Hu . . Chinese J Polym Sci , 2014 . 32 1218 - 1223 . DOI:10.1007/s10118-014-1495-9http://doi.org/10.1007/s10118-014-1495-9.

S Coppola , N Grizzuti , P L Maffettone . . Macromolecules , 2001 . 34 5030 - 5036 . DOI:10.1021/ma010275ehttp://doi.org/10.1021/ma010275e.

J F Ru , S G Yang , D Zhou , H M Yin , J Lei , Z M Li . . Macromolecules , 2016 . 49 3826 - 3837 . DOI:10.1021/acs.macromol.6b00595http://doi.org/10.1021/acs.macromol.6b00595.

O O Mykhaylyk , P Chambon , R S Graham , J P A Fairclough , P D Olmsted , A J Ryan . . Macromolecules , 2008 . 41 1901 - 1904 . DOI:10.1021/ma702603vhttp://doi.org/10.1021/ma702603v.

K H Kim , A Isayev , K Kwon . . J Appl Polym Sci , 2005 . 95 502 - 523 . DOI:10.1002/(ISSN)1097-4628http://doi.org/10.1002/(ISSN)1097-4628.

R J Steenbakkers , G W Peters . . J Rheol , 2011 . 55 401 - 433 . DOI:10.1122/1.3545844http://doi.org/10.1122/1.3545844.

J Sun , Y Song , Q Zheng , H Tan , J Yu , H Li . . J Polym Sci, Part B:Polym Phys , 2007 . 45 2594 - 2602 . DOI:10.1002/(ISSN)1099-0488http://doi.org/10.1002/(ISSN)1099-0488.

Z Nie , W Yu , C Zhou . . J Rheol , 2016 . 60 1161 - 1179 . DOI:10.1122/1.4961483http://doi.org/10.1122/1.4961483.

S Q Wang , S Ravindranath , P Boukany . . Macromolecules , 2011 . 44 183 - 190 . DOI:10.1021/ma101223qhttp://doi.org/10.1021/ma101223q.

C Huang , Q Chen , R Weiss . . Macromolecules , 2016 . 49 9203 - 9214 . DOI:10.1021/acs.macromol.6b02057http://doi.org/10.1021/acs.macromol.6b02057.

J Cao , A E Likhtman . . Phys Rev Lett , 2012 . 108 028302 DOI:10.1103/PhysRevLett.108.028302http://doi.org/10.1103/PhysRevLett.108.028302.

S Q Wang , S Ravindranath , P Boukany , M Olechnowicz , R P Quirk , A Halasa , J Mays . . Phys Rev Lett , 2006 . 97 187801 DOI:10.1103/PhysRevLett.97.187801http://doi.org/10.1103/PhysRevLett.97.187801.

S Zhu , Z Wang , F Su , W Zhou , N Tian , X Li , L Li . . J Rheol , 2013 . 57 1281 - 1296 . DOI:10.1122/1.4812671http://doi.org/10.1122/1.4812671.

S Q Wang , S Ravindranath , Y Wang , P Boukany . . J Chem Phys , 2007 . 127 064903 DOI:10.1063/1.2753156http://doi.org/10.1063/1.2753156.

Y Wang , S Q Wang . . J Rheol , 2009 . 53 1389 - 1401 . DOI:10.1122/1.3208063http://doi.org/10.1122/1.3208063.

S Cheng , S Q Wang . . J Rheol , 2012 . 56 1413 - 1428 . DOI:10.1122/1.4740264http://doi.org/10.1122/1.4740264.

K Cui , L Meng , N Tian , W Zhou , Y Liu , Z Wang , J He , L Li . . Macromolecules , 2012 . 45 5477 - 5486 . DOI:10.1021/ma300338chttp://doi.org/10.1021/ma300338c.

R H Somani , B S Hsiao , A Nogales , H Fruitwala , S Srinivas , A H Tsou . . Macromolecules , 2001 . 34 5902 - 5909 . DOI:10.1021/ma0106191http://doi.org/10.1021/ma0106191.

Y H Chen , Y M Mao , Z M Li , B S Hsiao . . Macromolecules , 2010 . 43 6760 - 6771 . DOI:10.1021/ma101006ehttp://doi.org/10.1021/ma101006e.

更多指标>

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Preparation and Characterization of PEs Grafted with Acrylic-based Monomers

Preparation of Low-shrinkage Polypropylene by Tailoring Crystallization

Preparation of High Performance Dielectric Elastomers by Tailoring the Aggregation Structure of Polyurethane

The Effect of Lamellar Thickness of iPP on the Formation of Trigonal Modification of PB-1 under Confinement Environment

Regulating the Crystallization Behaviors of High-molecular-weight Poly(lactic acid) Stereocomplex System Based on the Structure of Poly(ethylene glycol)

Related Author

No data

Related Institution

Key Laboratory of Automobile Materials of Ministry of Education, College of Materials Science and Engineering, Jilin University

SINOPEC Beijing Research Institute of Chemical Industry

College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University

State Key Laboratory of Organic-Inorganic Composites, Beijing University of Chemical Technology

Key Laboratory of Rubber-Plastics, Ministry of Education/Shandong Provincial Key Laboratory of Rubber-plastics, School of Polymer Science and Engineering, Qingdao University of Science & Technology

Postal code：100190
Tel：010-62588927 Email：gfzxb@iccas.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备05002797号-8 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰