STRUCTURE AND PROPERTY STUDIES OF LIQUID CRYSTALLINE POLY(ESTER IMIDE)/PET BLENDS

XIAO  Wen-Ming; ZHANG  Yi; CHENG  Kailiang; LIU  Siwei; CHI  Zhenguo; XU  Jiarui

doi:10.3724/SP.J.1105.2011.100119

您当前的位置：

首页 >

文章列表页 >

STRUCTURE AND PROPERTY STUDIES OF LIQUID CRYSTALLINE POLY(ESTER IMIDE)/PET BLENDS

Research Article | 更新时间：2021-03-19

- STRUCTURE AND PROPERTY STUDIES OF LIQUID CRYSTALLINE POLY(ESTER IMIDE)/PET BLENDS
- Acta Polymerica Sinica Issue 4, Pages: 402-408(2011)
- 作者机构：
- 作者简介：
- 基金信息：
- DOI：10.3724/SP.J.1105.2011.100119
  CLC：
- Published：20 April 2011，
扫描看全文
XIAO Wen-Ming, ZHANG Yi, CHENG Kailiang, LIU Siwei, CHI Zhenguo, XU Jiarui. STRUCTURE AND PROPERTY STUDIES OF LIQUID CRYSTALLINE POLY(ESTER IMIDE)/PET BLENDS. [J]. Acta Polymerica Sinica (4):402-408(2011)
DOI：

XIAO Wen-Ming, ZHANG Yi, CHENG Kailiang, LIU Siwei, CHI Zhenguo, XU Jiarui. STRUCTURE AND PROPERTY STUDIES OF LIQUID CRYSTALLINE POLY(ESTER IMIDE)/PET BLENDS. [J]. Acta Polymerica Sinica (4):402-408(2011) DOI： 10.3724/SP.J.1105.2011.100119.

摘要

通过熔融共混的方式，将实验室自行设计合成的三元共聚热致液晶聚酯酰亚胺（PPDI）与聚对苯二甲酸乙二酯（PET）进行共混，制备一系列不同液晶聚合物含量的共混体系.采用示差扫描量热仪（DSC）、广角X射线衍射仪（WAXD）和动态力学性能分析仪（DMA）对共混体系的结构与性能进行表征.结果表明，共混体系中两组份之间具有良好的相容性，表现出单一的玻璃化转变温度，且玻璃化转变温度明显高于基于Fox方程的理论计算值；液晶聚合物的加入对PET的结晶行为及结晶结构产生重要的影响，起到了明显的异相成核作用，大大提高了PET的结晶温度及结晶速率，并有利于其结晶度和结晶完善程度的提高和改善；PPDI对共混体系起到了显著的增强效果，体现为体系储能模量的提高，且其储能模量随着PPDI添加量的增加而增加；液晶PPDI的加入对共混体系的热稳定性影响不大，其起始分解温度较基体PET略有提高.

Abstract

The effects of terpolymer liquid crystalline poly(ester imide) (PPDI) on the structure and properties of its blend with semicrystalline polymer

poly(ethylene terephthalate) (PET) were studied.The PPDI was synthesized by our lab.The blend systems were prepared by melt blending

and the content of PPDI ranged from 0/100 to 10/90. Differential scanning calorimetry (DSC)

wide-angle X-ray diffraction (WAXD) and dynamic mechanical property analysis (DMA) were used to study the crystalline behavior

crystalline structure and dynamic mechanical properties of the blend system

as well as the miscibility of PPDI and PET.Results showed that the addiction of liquid crystalline terpolymer PPDI had strong effect on the crystalline behavior and crystalline structure of PET

which acted as heterogeneous nuclear agents

therefore increasing the initial crystallization point and crystallization rate of PET

and was of benefit to the increase of the degree of crystallinity and the perfection of crystallization.The blend systems show only one glass transition temperature (Tg)

and the Tgs are much higher than the theoretical results calculated by using Fox equation.Dynamic mechanical properties showed that storage modulus of the blend systems was higher than that of PET

and increased with the content of PPDI.These mean that PPDI has a reinforcing effect on PET. The thermal stability of the blend systems is a little higher than that of pure PET.

关键词

液晶聚酯酰亚胺PET共混结构性能

Keywords

Liquid crystalline poly(ester imide)PETBlendStructureProperties

references

更多指标>

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Polyphenylene Oxide Based Ion Exchange Membranes for Fuel Cells

The Effect of Synthetic Route on the Structure and Performance of Copoly(arylene ether nitrile)s Containing Phthalazinone Moieties

Effects of Dibenzocrown Ether and Diphenoxyethylene Diether Structural Units on the Properties of Degradable Polyhexahydrotriazine Thermosetting Resins

A Simulation Study of Enhancing the Compatibility in Block Copolymer AB/Homopolymer C Blends by Solvents

Related Author

No data

Related Institution

School of Chemistry and Materials Science, University of Science and Technology of China

Liaoning Province Engineering Center of High Performance Resins

Department of Polymer Science &amp

School of Chemistry and Chemical Engineering, Guangxi University for Nationalities

Key Laboratory of Chemistry and Engineering of Forest Products, State Ethnic Affairs Commission, Guangxi Key Laboratory of Chemistry and Engineering of Forest Products, Guangxi Collaborative Innovation Center for Chemistry and Engineering of Forest Products

Postal code：100190
Tel：010-62588927 Email：gfzxb@iccas.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备05002797号-8 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰