注射成型聚碳酸酯厚度截面的残余应力分析

郎建林; 王韬; 葛勇; 厉蕾; 颜悦

doi:10.11777/j.issn1000-3304.2017.16282

您当前的位置：

首页 >

文章列表页 >

注射成型聚碳酸酯厚度截面的残余应力分析

研究论文 | 更新时间：2021-03-19

- 注射成型聚碳酸酯厚度截面的残余应力分析
- Residual Stress Analysis in Cross Section of Injection-molded Polycarbonate
- 高分子学报 2017年第6期页码：999-1007
- 作者机构：
  
  北京航空材料研究院北京市先进运载系统结构透明件工程技术研究中心北京 100095
- 作者简介：
  
  颜悦, E-mail:Yue.yan@biam.ac.cn Yue Yan, E-mail:Yue.yan@biam.ac.cn
- 基金信息：
- DOI：10.11777/j.issn1000-3304.2017.16282
  中图分类号：
- 纸质出版日期：2017-6-20，
  
  收稿日期：2016-9-13，
  
  修回日期：2016-11-8，
扫描看全文
郎建林, 王韬, 葛勇, 厉蕾, 颜悦. 注射成型聚碳酸酯厚度截面的残余应力分析[J]. 高分子学报, 2017,(6):999-1007.

Jian-lin Lang, Tao Wang, Yong Ge, Lei Li, Yue Yan. Residual Stress Analysis in Cross Section of Injection-molded Polycarbonate[J]. Acta Polymerica Sinica, 2017,(6):999-1007.
郎建林, 王韬, 葛勇, 厉蕾, 颜悦. 注射成型聚碳酸酯厚度截面的残余应力分析[J]. 高分子学报, 2017,(6):999-1007. DOI： 10.11777/j.issn1000-3304.2017.16282.

Jian-lin Lang, Tao Wang, Yong Ge, Lei Li, Yue Yan. Residual Stress Analysis in Cross Section of Injection-molded Polycarbonate[J]. Acta Polymerica Sinica, 2017,(6):999-1007. DOI： 10.11777/j.issn1000-3304.2017.16282.

摘要

通过光弹法定量测量了注射成型聚碳酸酯（PC）试样在厚度截面上的残余应力，并结合模具温度的变化与不对称分布，对厚度截面上的残余应力分布进行了详细的研究.结果表明，在厚度截面上，试样边缘分布较高的流动残余应力，芯部分布较高的热残余应力，两区域界面处为流动应力与热应力相互耦合而形成的低应力过渡区；模具温度低于120℃时，PC的残余应力随模具温度的变化并不明显；模具温度高于120℃时，PC的残余应力随模具温度的升高显著降低；不对称模具温度会导致在低模温侧高热残余应力区分布宽，在高模温侧高热残余应力区分布窄.此外，试样的翘曲随模具温度的升高而逐渐增加，不对称模具温度会导致较大的翘曲.

Abstract

The residual stress in cross section of injection-molded polycarbonate (PC) was quantitatively measured by photo-elastic method. The effects of mold temperature on residual stress distribution in cross section and warpage of the whole sample were analyzed in detail. The results show that

in the cross section of the injection-molded PC

the high flow-induced residual stress exists in the skin near the wall of the mold

and the large thermal-introduced residual stress is mainly detected in the core. At the same time

there is a region with low residual stress between the core and the skin in cross section

formed by a mutual coupling of the flow-induced and the thermal-introduced residual stress. The distributions of those residual stresses are influenced by mold temperature. When mold temperature is lower than the heat distortion temperature of PC(126℃)

the residual stresses both in the core and the skin are hardly changedwithchanging mold temperatures. Whilethe mold temperature is higher than the heat distortion temperature of PC

the residual stress decreases significantly with increasing mold temperature. When the mold temperature is at 140 ℃

there are uniformresidual stresses in the cross section

and the average retardation measured byphoto-elastic method is 230nm

indicating a low residual stress. Furthermore

the warpage gets worse with increased mold temperature. When the temperatures in the movable and fixed mold are dissymmetry

the shape of the residual stress in the core is trapezoidal. This distribution is caused by uneven cooling. In the movable mold side with high temperature

the region of the thermal residual stress is narrow

and in the fixed mold side with low temperature

the stress is wide. The difference of the thermal residual distribution between the movable and the fixed mold side is more obviousas the mold temperature difference is increased. Finally

the residual stress distribution in a trapezoidal shape leads to a large warpage.

关键词

注射成型聚碳酸酯厚度截面残余应力模具温度

Keywords

Injection moldingPolycarbonateCross sectionResidual stressMold temperature

references

Shang Wei(尚伟). Experimental Research of Several Mechanics Problems for Toughened PMMA by Directional Stretching Process( 定向拉伸工艺增韧有机玻璃若干力学问题的试验研究). Doctoral dissertation of Tianjin University(天津大学博士学位论文), 2011

H T Wang , H M Zhou , Z G Huang , Y Zhang , H Y Qiao , Z P Yu . . Polym Test , 2016 . ( 50 ): 216 - 233.

Qing Chen , Yurun Fan , Qiang Zheng . . Acta Polymerica Sinica , 2007 . ( 5 ): 467 - 471 . http://www.gfzxb.org/CN/abstract/abstract10405.shtml.

陈青 , 范毓润 , 郑强 . . 高分子学报 , 2007 . ( 5 ): 467 - 471 . http://www.gfzxb.org/CN/abstract/abstract10405.shtml.

Xiahong Huang , Minqiang Yu , Chixing Zhou . . Advance in Mechanics , 2000 . 30 ( 2 ): 272 - 282 . DOI:10.6052/1000-0992-2000-2-J1998-022http://doi.org/10.6052/1000-0992-2000-2-J1998-022.

黄峡宏 , 余敏强 , 周持兴 . . 力学进展 , 2000 . 30 ( 2 ): 272 - 282 . DOI:10.6052/1000-0992-2000-2-J1998-022http://doi.org/10.6052/1000-0992-2000-2-J1998-022.

A I Isayev . . Polym Eng Sci , 1983 . 23 ( 51 ): 271 - 284.

A I Isayev , T H Lin , K Kwon . . Polymer , 2010 . 51 5623 - 5639 . DOI:10.1016/j.polymer.2010.09.055http://doi.org/10.1016/j.polymer.2010.09.055.

Ming Zhai , Yuanxian Gu , Changyu Shen . . Acta Polymerica Sinica , 2003 . ( 1 ): 35 - 38 . http://www.gfzxb.org/CN/abstract/abstract8823.shtml.

翟明 , 顾元宪 , 申长雨 . . 高分子学报 , 2003 . ( 1 ): 35 - 38 . http://www.gfzxb.org/CN/abstract/abstract8823.shtml.

bo Yan , Yang Li , Xiao Kong , Peng Zhao , Dequn Li . . Acta Polymerica Sinica , 2011 . ( 2 ): 173 - 179 . http://www.gfzxb.org/CN/abstract/abstract13322.shtml.

严波 , 李阳 , 孔啸 , 赵朋 , 李德群 . . 高分子学报 , 2011 . ( 2 ): 173 - 179 . http://www.gfzxb.org/CN/abstract/abstract13322.shtml.

R Wimberger-Friedl , J G Bruin , H F M Schoo . . Polym Eng Sci , 2003 . 43 ( 1 ): 62 - 70 . DOI:10.1002/(ISSN)1548-2634http://doi.org/10.1002/(ISSN)1548-2634.

Haimei Li , Changyu Shen , Wenli Xu , Kun Jiang , Xiazong Chen . . Plastics Industry , 2007 . ( 4 ): 12 - 16.

李海梅 , 申长雨 , 徐文莉 , 姜坤 , 陈夏宗 . . 塑胶工业 , 2007 . ( 4 ): 12 - 16.

N H Kim , A I Isayev . . Polym Eng Sci , 2013 . 53 ( 8 ): 1786 - 1808 . DOI:10.1002/pen.v53.8http://doi.org/10.1002/pen.v53.8.

F P T Baaijens . . Rheological Acta , 1991 . 30 ( 3 ): 284 - 299 . DOI:10.1007/BF00366642http://doi.org/10.1007/BF00366642.

M R Kamal , R Lai , J R Hernandez . . Polym Eng Sci , 2002 . 42 ( 5 ): 1098 - 1114 . DOI:10.1002/(ISSN)1548-2634http://doi.org/10.1002/(ISSN)1548-2634.

Guodong Xi , Huamin Zhou , Dequn Li . . Journal of Chemical Industry and Engineering , 2007 . 58 ( 1 ): 248 - 254.

奚国栋 , 周华民 , 李德群 . . 化工学报 , 2007 . 58 ( 1 ): 248 - 254.

James E M. Physical Properties of Polymers Handbook. New York: American Institute of Physics, 1996. 535-543

更多指标>

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

近红外吸收PC滤光片的制备与性能研究

有机催化CO₂/环氧/酸酐交替共聚合成聚碳酸酯/聚酯及其共聚物

氧化异丁烯与CO₂共聚物的合成及其结构与性能

丁香酚基双酚及聚硫醚碳酸酯的制备及性质研究

聚(1,4-环己二烯碳酸酯)立体低聚物的合成及微结构分析